Brad Point vs. Twist Bits: Which Drills Cleaner Holes in Wood

🪙 Free Woodworking Plans: Build a Transformer Bench that converts from picnic table to bench — Get the free plans →
Estimated Reading Time: calculating…

Reach for a drill and most people grab a twist bit, because a twist bit is what came in the case and it drills through anything. It will drill wood, and for a lot of holes that is completely fine. But set a twist bit next to a brad point bit and run both through the same board, and the difference shows up right away: one hole lands exactly where you marked it with a clean, sharp rim, and the other starts a little off to the side with a fuzzy, torn edge.

The two bits are shaped for different problems. A twist bit was designed for metal and adapted to everything else. A brad point was designed for wood and does one thing extremely well: it goes exactly where you put it and leaves a clean hole. Which one drills a cleaner hole is not really in question. The useful question is when that cleaner hole is worth reaching for the right bit, and when a twist bit is honestly the better call.

How Each Bit Actually Cuts

The whole difference lives in the tip. A twist bit ends in a cone, ground to a chisel edge across the very point, usually at a 118-degree included angle. That cone has nothing that locates it on a mark. Set the spinning point on a pencil line and the chisel edge skids across the surface until it happens to bite, which is why twist bits wander off the mark unless you dimple the center first. Behind the point, two cutting lips do the work, and the outer corners of those lips are the only part touching the rim of the hole. Those corners scrape rather than slice the fibers at the surface, and that is what leaves the fuzzy, slightly torn edge.

A brad point solves both problems with three added features. Dead center, a sharp spur (the brad) projects below everything else. You set that point directly on your layout mark and it stays there; the bit cannot walk. On either side, two outer spurs project ahead of the cutting lips. As the bit turns, those spurs score a clean circle into the surface, cutting the rim fibers before the lips arrive to lift the waste out of the middle. The fibers at the edge of the hole are severed, not torn, so the rim comes out crisp even in splintery species and across face grain.

Brad point tip versus twist bit tip Two drill bit tips in side profile. The brad point has a long central spur that projects below two outer spurs, which score the rim of the hole before the cutting lips lift the waste, producing a clean rim. The twist bit ends in a plain conical chisel point with no central locator and no scoring spurs, so it tends to wander on the mark and its outer corners tear the rim fibers. Brad point Twist bit center point scoring spurs chisel point outer corners Spurs cut the rim before the lips lift the waste, so the edge stays crisp. No locating spur, so it wanders on entry and frays the rim as it cuts.

That scoring action is the entire reason a brad point leaves a cleaner hole. It is also why a brad point is a wood-only tool. The fine spurs and the center point are shaped for wood fiber; run a brad point into metal or masonry and they dull or chip almost immediately, and the bit never cuts clean again.

💡 Tip: If a twist bit is the only size you have and the hole needs to land precisely, dimple the center first. A quick tap with an awl or a center punch gives the chisel point a divot to sit in so it cannot skate. On a drill press the quill holds the bit in line, so marking matters less; freehand, it is the difference between a hole on the line and a hole near it.

The Differences That Show in the Hole

Three things separate the finished holes, and they matter to different degrees depending on the work.

Placement. This is the brad point’s biggest practical edge. When you are drilling dowel holes, hardware locations, or anything that has to line up with a matching hole in another part, a bit that starts exactly on the mark saves you from cumulative error. A twist bit that wanders a sixteenth of an inch on each of eight holes turns a dowel joint into a fight.

Rim cleanliness on the entry face. The brad point wins here too, and you can see it. On plywood, veneered panels, and any hole that will show, the scored rim of a brad point hole looks finished, while the torn rim of a twist-bit hole needs sanding or a countersink to clean up. On hidden holes it makes no difference at all.

Blowout on the exit face. This one is a wash, and it is the point most people get wrong. Both bits splinter the back of the board when the tip breaks through, because nothing is supporting the fibers on the far side. The brad point’s spurs help a little, but neither bit gives you a clean exit on its own.

💡 Tip: Clamp a scrap backer board tight against the exit face before you drill through. With solid wood pressed against the back, the fibers have something to push against and cannot splinter outward, so both bits break through clean. This single step does more for the quality of a through-hole than the choice of bit does.

There is one more difference that has nothing to do with the hole itself: versatility. A twist bit drills wood, metal, plastic, and drywall with the same bit. For large flat-bottomed holes you would reach for a Forstner or a spade instead, but for ordinary round holes the twist bit is the one tool that crosses materials. A brad point does a single material beautifully and nothing else.

✎ Getting Clean, Placed Holes

A set of brad points covers dowel work, hardware layout, and any hole that shows on the face. Buying a range of sizes up front means you have the right diameter for standard dowels and hinge hardware without improvising with a twist bit that wanders.

Brad Point Bit Set Metric Dowel Bits

Choosing by Job: A Direct Reference

The choice comes down to whether placement and rim cleanliness matter for the hole in front of you, and whether wood is the only thing you are drilling.

→  Dowel holes, visible holes, precise hardware layout · brad point; exact placement and a clean rim are the whole job
→  Plywood, veneer, or splintery species on a show face · brad point, to score the rim clean
→  Rough or hidden holes, pilot holes, general shop drilling · a twist bit is faster to grab and cheaper to dull
→  Metal, plastic, or mixed materials · a twist bit; a brad point would be ruined
→  A hole that has to be dead-on with no drill press · brad point, because the center spur does what a steady hand cannot

That last case is worth sitting with, because it is where the brad point quietly earns its cost. Freehand, without a drill press to hold the bit square and on-center, a twist bit relies entirely on your setup and your steadiness. The brad point’s center spur removes that variable. It locks the start onto the mark before the bit has any chance to wander, which is exactly when handheld drilling goes wrong. For repeatable, placed holes with nothing but a cordless drill, that single spur is the difference.

Common Mistakes

Using a twist bit for dowel holes. Dowel joints depend on holes that line up across two parts. A wandering twist bit stacks small placement errors until the parts will not seat. Brad points exist largely for this job; use them, and drill from a marked, punched, or jig-guided center.

Running a brad point into metal or a hidden screw. One pass through a nail, a screw, or a metal plate takes the edge off the spurs and the center point, and a dulled brad point tears rather than scores. Keep a set of brad points for wood only, and reach for a twist bit anywhere metal might be hiding.

Blaming the bit for exit blowout. Tearout on the back face is a support problem, not a bit problem, and no bit fixes it alone. Back the workpiece with scrap, or drill until the center point just pierces the far face, then finish the hole from the other side.

Drilling wood at metal speeds. Wood cuts clean at moderate to high speed with steady feed, but high speed with a stalled feed burns the hole wall, especially in cherry and maple. Let the bit cut; if you see smoke or smell scorching, slow down or clear the chips more often.

Skipping a pilot for large brad points. Above roughly three-eighths of an inch, a big brad point’s center spur can grab and jerk in a handheld drill. A small pilot hole gives the waste somewhere to go and keeps the bit from lurching as it starts.

🔨 General-Purpose Drilling

A quality twist bit set is the workhorse for pilot holes, rough work, and anything that is not wood. Pair it with a center punch so the conical point starts on your mark instead of skating past it.

Twist Drill Bit Set Automatic Center Punch

🔫 Free Woodworking Plans for Beginners

Download step-by-step plans for beginner-friendly builds, including our popular Transformer Bench that converts from a picnic table into a bench and back again.

Download Free Plans →
Affiliate Disclosure: This post may contain affiliate links. If you purchase through these links, we may earn a small commission at no additional cost to you.

Frequently Asked Questions

Can brad point bits drill metal?

No. The center spur and the outer scoring spurs are ground for wood fiber and dull or chip almost instantly in metal, after which the bit tears instead of scoring. Use a twist bit or a metal-specific bit for metal, and keep brad points for wood only.

Why does my twist bit wander when I start a hole?

The conical chisel point has no locating feature, so it skates across the surface until it bites. Dimple the center with an awl or center punch first, or start at low speed with light pressure. A drill press largely removes the problem by holding the bit in line.

Do brad point bits stop tearout completely?

On the entry face, mostly yes; the scoring spurs cut the rim clean. On the exit face, no. Both bit types blow out the back when they break through unless you clamp a backer board behind the work.

Are brad point bits worth it for a beginner?

If you drill dowel holes or any holes that show, yes; the clean rim and exact placement remove a whole class of frustration. If your drilling is mostly pilot holes and rough work, a good twist bit set covers it and does double duty in metal and plastic.

What is the difference between a brad point and a Forstner bit?

A brad point drills a round through-hole with clean walls and a small center dimple at the bottom. A Forstner drills a flat-bottomed hole and a cleaner large-diameter hole, but it removes more material and usually wants a drill press. For clean pilot and dowel holes, use a brad point; for flat-bottomed or large holes, a Forstner.

Can I sharpen brad point bits?

You can, but it is fiddly. The center point and the two spurs each need attention and the geometry is easy to ruin by hand. Twist bits are far easier to sharpen, by hand or with a jig, so for most people brad points get replaced rather than sharpened once they dull.